How to Set Up a Mixer for a Multi-Host Podcast

Tutorials · September 29, 2026 · 5 min read

Need to set up a mixer for two or three hosts without all the hassle? Good news. It’s mostly about signal flow, gain, and a repeatable procedure. Memorize them once, and all mixers begin to make sense. This article will take you through the process of creating a mixer for a multi-host podcast.

Why a Mixer Helps

If multiple people are speaking in a single room, you must have control over each voice. In a mixer, each microphone has its own channel with a gain control knob, a fader, and a mute button. Adjust volume for voices, mute a microphone that is not in use, and route audio to any microphone or location.

It provides each host with a headphone feed also. Oh, and you can throw in a phone and a music player.

Step 1: Plan Your Signal Flow

Before you plug anything in, sketch what connects to what.

  • Microphones: Each mic goes into its own input channel.
  • Main outputs: These feed your recorder or, if your mixer has USB, your computer.
  • Headphone outputs: One per host, or use a headphone amplifier to serve everyone.
  • Auxiliary send: This carries the mix-minus feed for remote guests.

Stick a strip of tape under each fader and write the host’s name on it. It’s a tiny job that saves a lot of confusion mid-recording.

Step 2: Set the Gain Properly

The most critical control of any channel is gain. It will kill you if you get it wrong and there’s no water downstream of you.

  1. Put all faders to their nominal (usually 0) setting.
  2. Have one host use their normal volume to speak.
  3. Adjust the gain until the meter reads reasonable levels, with the “odd peak”.
  4. Ensure that the clip light doesn’t activate.
  5. Do this for each microphone.

Provide more gain to the quieter host. Rather, don’t push their fader up. Having faders at the same level allows you to make adjustments at the show.

Step 3: Phantom Power, Filters and Tone

Before you press record, make a quick inspection of a few switches.

  • Phantom power: Only use this feature when necessary, for condenser mics only, and after the mic is plugged in. It is not necessary for dynamic mics.
  • Low cut filter – This cuts out droning noises such as rumble, desk thumps, etc., that are lower than the voice range. Use it on all speech channels.
  • EQ: Keep it light. Address issues at the source – use improved mic placement and a quieter room.

Step 4: Balance the Main Mix

Now bring all the faders up and have everyone chat. Try to keep all the voices at the same level and monitor to keep the overall signal below clipping.

The voice of pan is slightly separated for a stereo show. Prefer mono? Keep everything centred.

Mute any channel that isn’t in use. Eliminates background noise and bleed. And when two mics capture the same voice, you’ll hear a hollow, phasered sound. The solution is easy: make sure that each mic is near its speaker, and put mics away from each other.

Step 5: Sort Out Headphones and Monitoring

All hosts must have their sound and others’ sound heard. Sharing is the easy way: the main mix via a headphone amplifier. Want more control? Create separate monitor mixes with auxiliary sends to have a little more volume for each individual.

Never check into through speakers when mics are on. You will receive an echo or the dreaded howl! Moderate volume closed-back headphones are recommended.

Step 6: Add Remote Guests With Mix-Minus

A remote guest should hear everyone except themselves. If their voice returns slightly delayed, they will be thrown off and likely cease speaking. That is not really ideal or suitable. Mix-minus remedies this by passing the guest the entire mix minus their channel. On many mixers, this is how it works:

  • Send the guest’s audio track to a separate track.
  • Set that channel’s aux send to zero.
  • Send each of the other channels to the aux output.
  • Plug the aux out into call software.

The routing will be different depending on the model; please consult your manual for exact steps.

Step 7: Record a Test

If your mixer has USB audio, select it as the input in your recording software and capture a short test. Listen on headphones for hum, distortion, or uneven levels. If the mixer allows it, record each mic on a separate track. Editing gets much easier. If not, record the main mix.

Before every show, run this checklist:

  • Cables: Everything plugged in firmly and labelled.
  • Phantom power: On for condensers only.
  • Gain: Set per host, no clipping.
  • Faders: Near nominal, balanced.
  • Headphones: Working for every host.
  • Mix-minus: Tested with your remote guest.
  • Recording: Armed and confirmed.

Conclusion

When using a mixer for a multi-host show, plan signal flow, set gain per host, and only use phantom power when necessary. Balance the main mix, provide headphone feeds to all, and create a mix-minus for remote guests. Then test, take notes, and repeat the process each time. A routine turns a threatening panel into the one you can rely on.

Ready to build your setup? Browse our mixers and audio consoles category. For microphones, the Shure SM58 is a trusted dynamic option, while the MAONO PM320S needs phantom power. If your mixer feeds SDI video, the Audio to SDI 2 embeds mixer audio straight into your SDI signal.

FAQs

What is mix-minus?

It’s a feed that sends a remote guest’s audio to everyone except themselves, so they don’t hear their own voice delayed.

How do I set gain on a mixer?

Set faders to nominal, speak at your normal level, and adjust gain until peaks look healthy without clipping.

Do I need phantom power?

Only for condenser mics that require it. Dynamic mics generally don’t.

Build a Better Studio. One Upgrade at a Time.

Get practical equipment guides, studio tips, and new product recommendations delivered to your inbox.

We will only use your email to send the newsletter. Unsubscribe at any time.