Beginner Podcast Studio

A realistic, step-by-step guide to building a simple podcast studio at home: room, microphone, interface, headphones and a first test recording.

Built for: First-time podcasters recording alone or with one guest

Equipment list

This guide takes you from an empty desk to a working podcast studio, in the order that makes the biggest difference to your sound. It assumes you are recording yourself, or yourself plus one guest, in a normal room at home. You do not need a soundproof booth, and you do not need to buy everything on day one.

Step 1: Decide what you are building

Before buying anything, answer three questions. Will you record alone or with others in the room? Will you publish audio only, or video as well? And do you want the fastest possible start, or a setup you can grow?

The answers point you to one of two paths. Path A is a USB microphone, such as the Blue Yeti: one cable to your computer, no extra equipment, ready in minutes. Path B is an XLR microphone plus an interface, such as the Shure SM58 and the Behringer MIC500USB: more parts to buy, but each part can be upgraded later and you can add a second voice. Our guide to XLR vs USB microphones compares both routes in detail. The rest of this guide covers both.

Step 2: Choose and test your room

Your room affects the sound as much as your microphone. Hard, empty rooms reflect sound and make recordings echoey. Pick the room in your home with the most soft surfaces: carpet, curtains, a bed, a sofa, bookshelves. Small bedrooms often beat large living rooms.

Do a simple test before you commit. Stand where you plan to sit and clap once, sharply. If you hear a ringing flutter after the clap, the room is reflective and needs softening. Also listen for noise you cannot hear while concentrating: a refrigerator, a fan, an air conditioner, traffic. Turn off what you can, and close the windows and the door.

If the room is hard, add soft things before buying anything: hang heavy curtains or duvets on bare walls, put a rug on a hard floor, and place cushions or a bookcase behind you. A wardrobe full of clothes makes a surprisingly good emergency booth. Our article on improving podcast audio without buying gear goes into this in more detail.

Step 3: Set up the desk and microphone position

Place the desk away from the middle of the room and avoid sitting with your back to a bare wall. Put the computer where its fan is as far from the microphone as you can manage, or use a quiet setting.

Mount the microphone on a stand or boom arm instead of leaving it on the desk, where it will pick up typing and bumps. Position it close to your mouth, a few fingers’ width to a hand’s width away depending on the microphone, and slightly off to one side or above your mouth to reduce plosives. Our guide to choosing a boom arm explains weight ratings and reach. Check the weight against your microphone before buying.

Keep your hands off the desk while recording. Taps travel up the stand into the microphone.

Step 4: Connect the equipment

Path A (USB microphone). Connect the Blue Yeti to a USB port on your computer. Plug your headphones into the microphone’s 3.5 mm headphone output, which its listing says is zero-latency, so you hear yourself with no delay. Set the pickup pattern to cardioid for solo speech, which favours the sound in front of the microphone. Set the gain low to start. The listing notes audio is limited to 16-bit at 48 kHz, which is fine for speech.

Path B (XLR microphone and interface). Screw the SM58 into its stand or arm, connect an XLR cable from the microphone to the interface’s microphone input, and connect the interface to your computer by USB. The MIC500USB needs mains power, so plug in its power supply as well. Plug your headphones into the interface’s headphone output. Dynamic microphones like the SM58 need clean gain, so check the interface’s specified gain range, as explained in our Shure SM58 for podcasting article. Do not use phantom power with a dynamic microphone unless the manufacturer says it is safe.

Use wired closed-back headphones on either path. Wireless headphones add delay and are poor for monitoring. If you are unsure which type to buy, read closed-back vs open-back headphones.

Step 5: Set up your recording software

Install recording software. Many beginners use a free audio editor, and Behringer provides recording and podcasting software as a free download with the MIC500USB according to its listing. In the software’s settings, choose your microphone or interface as the input and your headphones as the output. Set the sample rate to 48 kHz, which matches common podcast and video workflows.

Create a new project, arm a track for recording, and make sure you can see the level meter move when you talk. If you hear yourself twice, with a slight echo, you are monitoring in two places. Switch off software monitoring and use the direct monitoring on the microphone or interface, as explained in audio latency and direct monitoring.

Step 6: Set your levels

Levels decide whether your recording is clean or noisy. Speak at your normal volume and raise the gain until the loudest parts reach roughly minus twelve to minus six decibels on the software meter. Then speak loudly, laugh, and check it never touches zero. A recording that is too quiet gets noisy when boosted later, and a clipped one cannot be repaired.

Leave the gain where it is once you have set it, and do not change it between episodes unless you change something in the setup.

Step 7: Record a two-minute test

Record two minutes of you speaking as you would in an episode, including a loud moment. Then put on your headphones and listen critically. Listen for echo, hiss, hum, mouth clicks and plosives. Then listen on something else, such as your phone, because your audience will.

Fix one thing at a time. Echo means more soft furnishings or moving closer. Hiss means too much gain or a weak preamp. Hum often means a cable or power source problem. Harsh p sounds mean speak slightly off-axis or add a foam cover. Test again after each change.

Step 8: Add a guest or video (optional)

For a guest in the room, the simplest upgrade is a second microphone and a two-input interface or a small mixer, as covered in audio interface vs mixer. For a remote guest, ask them to wear headphones and record in a soft room.

If you publish video, add a camera and a soft key light. Our guide to three-point lighting explains placement, and our lighting and cameras categories list options.

Step 9: Build a pre-recording routine

  • Close the door and windows, and silence phones and notifications.
  • Check cables are seated and the microphone is at the same distance as last time.
  • Put on headphones and check the meter while you speak.
  • Record ten seconds of silence, which gives you a noise sample for editing.
  • Do a short test, listen back, and then start the episode.

Troubleshooting

  • The computer does not see the microphone. Try another USB port, avoid hubs, and check the input selection in your software and operating system.
  • The recording is very quiet. Check gain, make sure you are speaking into the correct end of the microphone, and move closer. With an XLR dynamic microphone, check the interface has enough gain.
  • There is hum or buzz. Move cables away from power leads, try another cable, and unplug other devices one at a time.
  • The recording sounds echoey. Add soft furnishings, move closer to the microphone, and avoid recording near bare walls.

Once you are recording reliably, work through our broadcasting equipment checklist to decide what to upgrade next.

Videos to watch

Short tutorials that go with the steps above. These open on YouTube.

Where to spend first

Spend in this order: first the microphone path (a USB microphone, or an XLR microphone plus interface), then closed-back headphones, then room treatment using soft furnishings you may already own, then a boom arm, and only then lighting. Prices change often, so check current prices on Amazon before you decide.

Upgrade options

  • Add a second microphone and move to a two-input interface or a small mixer when you bring in a co-host.
  • Add a pop filter or foam windscreen if you hear harsh p and b sounds.
  • Add acoustic panels at the first reflection points once soft furnishings have taken you as far as they can.
  • Add a camera and key light when you are ready to publish video, using our YouTube Studio build as a guide.